Clik here to view.
Create a symbol from layout
I have created a symbol by momentum for a transformer in 65nm technology but when i use mentioned symbol in a schematic and try to run LVS, but i have gotten error consider that the symbol could not...
View ArticleClik here to view.
RE: QRC conflictiong name spaces
Hi Saloni, thank you for your help, I now fixed the "conflicting name spaces" warning as you explained. I was actually running the QRC-FS extraction on selected nets. The warning doesn't show up...
View ArticleClik here to view.
RE: ade explorer set instance value
thanks, Andrew, i am new man for ic design, finally, i simulated one single end LNA and chose the port as my source, and set the source type to sine, then 3 parameters set here, frf is working...
View ArticleClik here to view.
RE: ade explorer set instance value
Can you find the PORT0 component in the netlist (input.scs) and paste the entire line (may be several lines) here? It doesn't look as if it is generating any small signal in the hbac. Regards, Andrew.
View ArticleClik here to view.
RE: QRC conflictiong name spaces
Hi, There's nothing in the command file that could explain the missing coupling cap, and it's unusual for an extractor to miss hundreds of fF. Are you getting any other Cc extracted to the net...
View ArticleClik here to view.
RE: how to set a bindkey to display multiple layers ?
HI Nhumai, ;Usage: Bindkey 0 makes all layer invisible except layer "ref" "drawing" in layout. hiSetBindKey("Layout" " 0" "visibility_0()") procedure(visibility_0() leSetEntryLayer(list("ref"...
View ArticleClik here to view.
How to export NCDrill, NCRoute in SKILL
Hello, I've been trying to find the solution to this for quite some time, searched all over the forums, but not able to get the information I need. I am trying to use SKILL to automate exporting...
View ArticleClik here to view.
Export transient waveform into ASCI/CSV format for psfxl simulation data
I used to use the psf function $CDS_INSTALL_DIR/bin/psf to output transient waveform into an asci format. Is it possible to use the psf function to do do this on a psfxl transient data? If no, is there...
View ArticleClik here to view.
OrCAD 17.2 Legacy UI - how to change back
Hi I'm new to OrCAD and when I was messing around I decided to click the change to legacy UI (requires restart) and it worked but now I can't find where anything is so how do I change it back from the...
View ArticleClik here to view.
RE: Export transient waveform into ASCI/CSV format for psfxl simulation data
As far as I know there isn't a command to do this in the current IC releases. Regards, Andrew.
View ArticleClik here to view.
RE: ade explorer set instance value
Hi, Andrew, i made one mistake when i set the port, pac need hb input and the two signal should be same level, but i set the pac small signal level to another prf_pac, so the hb only sweep one signal,...
View ArticleClik here to view.
Virtuoso L and virtuoso xl cost ?
Hi All, How much does Cadence Virtuoso L cost and Virtuoso XL cost ? Because I want to compare their prices. Best regards, Marben
View ArticleClik here to view.
problem with resistor in corner analysis
hi i am designing a circuit (transimpedance amplifier ) that has a few resistors .. i want to do corner analysis and when i use resistors from tsmc library it gives errors and says that these resistors...
View ArticleClik here to view.
RE: OrCAD 17.2 Legacy UI - how to change back
Setup>User Preferences, Ui, General, uncheck orcad_use_legacy_menu and restart.
View ArticleClik here to view.
RE: How to export NCDrill, NCRoute in SKILL
The 'debug' mode can be useful as described in the axlRunBatchDBProgram() documentation: For debug, set the env variable, wait_debug, on the Allegro command line: set wait_debug or in Skill...
View ArticleClik here to view.
hiRegCurWindowTrigger usage
Hi, What is this function hiRegCurWindowTrigger? How to use this? I tried the following procedure(testPrint(win) printf("%L\tgot modified", win) ) hiRegCurWindowTrigger('testPrint) -Ramakrishnan
View ArticleClik here to view.
RE: hiRegCurWindowTrigger usage
Hi Ramakrishnan, The documentation seems pretty clear to me. It does get passed a window number rather than a window id, so you'd have to use window(win) to get the corresponding window id. What is...
View ArticleClik here to view.
RE: Virtuoso L and virtuoso xl cost ?
Hi Marben, Cadence doesn't publish such information on a public forum, and customers are not allowed to reveal this information under the terms of their agreement. You would need to contact your...
View ArticleClik here to view.
RE: ade explorer set instance value
Was just about to point that out, but see you've spotted the error yourself. Regards, Andrew.
View ArticleClik here to view.
RE: problem with resistor in corner analysis
Without knowing which PDK (there are a lot of different TSMC processes) you're using, I doubt anyone can help you. It might also be difficult to respond without breaking the foundry's NDA - so it would...
View Article